|
Subject |
Started by  |
Replies |
Views |
Last post |
|
|
Thanks VW Gasser Garage
|
BossHogg76
|
0
|
3295
|
March 07, 2013, 16:37:03 pm
by BossHogg76
|
|
|
|
Hot Vw magazine request
|
BossHogg76
|
2
|
6179
|
September 03, 2017, 20:23:59 pm
by BossHogg76
|
|
|
|
Boss Hoggs EBI 8 Trip.
|
BossHogg76
|
14
|
11230
|
October 12, 2019, 13:11:18 pm
by Nico86
|
|
|
Bosshoggs trip to the 1967 50th Anniversary Show
|
BossHogg76
|
21
|
17394
|
July 12, 2017, 08:43:52 am
by wolfswest
|
|
|
|
Is LandDProducts California Still trading?
|
BossHogg76
|
9
|
7536
|
March 27, 2015, 18:22:30 pm
by BossHogg76
|
|
|
|
Where to start on an engine build
|
BossHogg76
|
11
|
7670
|
January 06, 2011, 01:22:29 am
by fredy66
|
|
|
|
Colours, Help!!! I can't stop changing my mind on paint.
|
BossHogg76
|
13
|
10563
|
August 15, 2013, 18:14:29 pm
by iowa mark
|
|
|
|
Help trying to identify a car
|
BossHogg76
|
3
|
4280
|
December 04, 2012, 17:44:47 pm
by BossHogg76
|
|
|
|
Old aftermarket brochures
|
bottom rung
|
4
|
3984
|
November 22, 2010, 02:35:26 am
by Rick Meredith
|
|
|
|
Single HD valve spring recommendation
|
Brandon Sinclair
|
12
|
9968
|
March 27, 2010, 01:44:34 am
by morkrieger
|
|
|
|
Anyone have the numbers or results from the CB Dyno Day this past weekend?
|
Brandon Sinclair
|
8
|
5842
|
November 05, 2009, 04:00:36 am
by 58vw
|
|
|
|
Machined sand seal-do you use a spacer for the crank pulley?
|
Brandon Sinclair
|
0
|
3581
|
July 04, 2009, 08:15:46 am
by Brandon Sinclair
|
|
|
|
Are spark plug wires with decent length boots available?
|
Brandon Sinclair
|
1
|
3646
|
February 23, 2012, 04:29:24 am
by Jim Ratto
|
|
|
|
Please help me with degreeing a camshaft.
|
Brandon Sinclair
|
14
|
8959
|
February 13, 2013, 17:28:48 pm
by Shag55
|
|
|
|
How often do you replace your spark plug wires, plugs, distributor cap and rotor
|
Brandon Sinclair
|
2
|
3543
|
June 01, 2011, 15:58:37 pm
by team97
|
|
|
|
What are you using for break in oil nowadays?
|
Brandon Sinclair
|
3
|
4479
|
July 06, 2009, 14:14:04 pm
by RMS Boxer Service
|
|
|
|
What are you guys using for oil pumps nowadays?
|
Brandon Sinclair
|
22
|
12974
|
June 08, 2010, 11:54:29 am
by Felix/DFL
|
|
|
|
Koni red settings and bump stop source
|
Brandon Sinclair
|
17
|
22242
|
October 29, 2020, 07:57:32 am
by Glauco
|
|
|
|
Rear wheel bearing question for IRS
|
Brandon Sinclair
|
1
|
3795
|
August 27, 2009, 01:23:48 am
by richie
|
|
|
|
Slip joint leaking on merged header driving me nuts
|
Brandon Sinclair
|
7
|
7708
|
September 21, 2012, 15:14:16 pm
by Brandon Sinclair
|
|
|
|
Recommendations needed to remove carbon from disassembled engine head
|
Brandon Sinclair
|
7
|
5323
|
March 26, 2010, 02:34:44 am
by 61SNRF
|
|
|
|
Used cam with new lifters experiences?
|
Brandon Sinclair
|
5
|
6518
|
June 11, 2009, 03:12:26 am
by Dave Rosique
|
|
|
|
Steps in combustion chambers..yes or no??
|
Brandon Sinclair
|
9
|
5631
|
December 07, 2009, 23:42:42 pm
by 181
|
|
|
|
What kind of exhaust gaskets do you use?
|
Brandon Sinclair
|
20
|
12761
|
May 31, 2013, 05:23:41 am
by Bruce
|
|
|
|
Do you guys adjust your valves differently from stock when running big cams?
|
Brandon Sinclair
|
1
|
3317
|
February 23, 2011, 19:11:43 pm
by Jim Ratto
|
|
|
|
What kind of hand cleaner do you use/recommend?
|
Brandon Sinclair
|
19
|
10936
|
July 08, 2010, 23:56:04 pm
by deano
|
|
|
|
Rod side clearance
|
Brandon Sinclair
|
5
|
6023
|
March 16, 2009, 16:30:23 pm
by Jim Ratto
|
|
|
|
Installing heads without pushrods tubes 1st to allow sealant to set up
|
Brandon Sinclair
|
13
|
10265
|
May 18, 2010, 22:38:16 pm
by Brandon Sinclair
|
|
|
|
Mahle main bearings partially covering oil holes
|
Brandon Sinclair
|
4
|
5177
|
March 16, 2009, 19:35:53 pm
by Brandon Sinclair
|
|
|
|
What does tranny maintenance consist of???
|
Brandon Sinclair
|
8
|
5754
|
December 28, 2009, 04:00:01 am
by DKK Robert
|
The Cal-look Lounge
Topic you have posted in
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll
