Title: Straight muffler solution for 2" header Post by: gator_push on December 25, 2011, 22:32:06 pm Hi there,
looking for a short muffler connecting straight to the 2" A1 header. Basically a short stinger style exhaust with muffler capabilities. I am not looking for a solution where a standard aftermarket muffler is welded to a pipe on a flange because of the exposure to the back. Are there any companies out there making such race exhaust systems? Title: Re: Straight muffler solution for 2" header Post by: John Palmer on December 25, 2011, 23:16:26 pm We run a A-1 sidewinder system that Tiger made with a custom muffler. The Sidewinder system is standard, but the muffler (actually two different sizes) is quick realease mounted with a stainless V-Band clamp. Just past the stainless clamp, the collector was made with "different sized" venturi cones before going into a bullet "straight through" muffler. The muffler exits straight out the side, just past the right rear tire. It's been on the car for the last four seasons and works flawlessly. We have never needed to used the small collector/muffler, because the car has always had good low end performance. Although this system was built as a "track legal" muffler system, it would also work well on the street. It tucks up under the car nicely, and does not drag when the car is loaded on the trailer, or during wheelies, lol.
Title: Re: Straight muffler solution for 2" header Post by: kingsburgphil on December 26, 2011, 07:48:39 am Hi there, I'm not sure of exactly of what you're looking for. Both of these examples are from A-1. My best advice ..give Tiger a call ;)looking for a short muffler connecting straight to the 2" A1 header. Basically a short stinger style exhaust with muffler capabilities. I am not looking for a solution where a standard aftermarket muffler is welded to a pipe on a flange because of the exposure to the back. Are there any companies out there making such race exhaust systems? Title: Re: Straight muffler solution for 2" header Post by: Troy Palmer on December 26, 2011, 08:07:33 am The Bullet John spoke of above is currenty on ebay.
Thanks Troy (AKA- empijones) Title: Re: Straight muffler solution for 2" header Post by: fredy66 on December 26, 2011, 14:05:38 pm Hi there, I'm not sure of exactly of what you're looking for. Both of these examples are from A-1. My best advice ..give Tiger a call ;)looking for a short muffler connecting straight to the 2" A1 header. Basically a short stinger style exhaust with muffler capabilities. I am not looking for a solution where a standard aftermarket muffler is welded to a pipe on a flange because of the exposure to the back. Are there any companies out there making such race exhaust systems? nice car Title: Re: Straight muffler solution for 2" header Post by: gator_push on December 26, 2011, 17:26:55 pm The Bullet John spoke of above is currenty on ebay. Troy,Thanks Troy (AKA- empijones) thanks for this information. I browsed on ebay, there are actually a couple of bullet-style mufflers. Can you post a link? Thanks, Peter Title: Re: Straight muffler solution for 2" header Post by: Lids on December 26, 2011, 19:38:44 pm The Bullet John spoke of above is currenty on ebay. Troy,Thanks Troy (AKA- empijones) thanks for this information. I browsed on ebay, there are actually a couple of bullet-style mufflers. Can you post a link? Thanks, Peter do a seller search on ebay.com for empijones and you will fine it. Title: Re: Straight muffler solution for 2" header Post by: . on December 27, 2011, 15:06:15 pm Here you go !
http://www.ebay.com/itm/Vintage-Cal-Look-Aircooled-NOS-VW-Racing-street-A-1-Muffler-v-band-bullet-empi-/110798452610?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item19cc1a3782 Title: Re: Straight muffler solution for 2" header Post by: Udo on December 27, 2011, 18:48:02 pm http://www.burnsstainless.com/
These are nice ones :) Udo Title: Re: Straight muffler solution for 2" header Post by: gator_push on December 29, 2011, 17:00:08 pm http://www.burnsstainless.com/ Indeed. Which size do you recommend Udo?These are nice ones :) Udo Title: Re: Straight muffler solution for 2" header Post by: Udo on December 29, 2011, 19:21:36 pm Next year you have enough power , so you do not have to look for the weight :)
I think 3" is ok , but i have someone who changes a stinger to a muffler , i will try this . i need another one too next year because i can not run the 2 mufflers with wheeliebars Udo Title: Re: Straight muffler solution for 2" header Post by: gator_push on December 30, 2011, 15:51:32 pm Next year you have enough power , so you do not have to look for the weight :) So be it. ;D |