|
Title: Raceengine Parts Post by: Otto/DFL on September 11, 2016, 19:20:54 pm Hi I'm selling Jürgen Kirschbaum former 11,3 sec Race Engine in Parts:
US injection case freshly spindled first over, type 4 main and for flanged 86 mm crank and 94mm bore incl. a set main bearings Scat/Mahle, 8mm Headstuds 700,- Euro 5,5" Scat con rods, Chevy Journal ready for 86mm stroker 180,- Euro Special made 95mm JE Pistons only 514gr incl rings, bolt and clips 400,- Euro CB Comp Ellis handported by Udo Becker 48x40mm titanium valves, Crower valvesprings and retainers, matchported manifolds shortened and narrowed for 51mm IDA's 1.250,- Euro Bugpack flanged crank with crack and flywheel for 200mm Clutch 250,- Euro Cam UB 36 aka FK 97 with chromo push rods 150,- Euro shipping worldwide bye Otto Title: Re: Raceengine Parts Post by: Otto/DFL on September 11, 2016, 19:24:18 pm Photos:
[attachment=1][attachment=2][attachment=3] Title: Re: Raceengine Parts Post by: Otto/DFL on September 11, 2016, 19:29:04 pm [attachment=1][attachment=2][attachment=3]
Title: Re: Raceengine Parts Post by: Otto/DFL on September 11, 2016, 19:30:39 pm even more!
[attachment=1][attachment=3] Title: Re: Raceengine Parts Post by: Otto/DFL on September 11, 2016, 19:32:18 pm more:
[attachment=1][attachment=2][attachment=3] Title: Re: Raceengine Parts Post by: Otto/DFL on September 11, 2016, 19:34:07 pm more:
[attachment=1][attachment=2][attachment=3] Title: Re: Raceengine Parts Post by: Otto/DFL on September 11, 2016, 19:36:51 pm more:
[attachment=1][attachment=2][attachment=3] Title: Re: Raceengine Parts Post by: Otto/DFL on September 25, 2016, 16:10:24 pm UP! ;)
Title: Re: Raceengine Parts Post by: kever65 on September 26, 2016, 19:29:20 pm What cilinders do you use with these pistons ?
Davy Title: Re: Raceengine Parts Post by: Otto/DFL on September 27, 2016, 11:30:41 am Hi Davy!
You have to hone 94mm Mahle or AA Cylinders! Bye Otto Title: Re: Raceengine Parts Post by: Tobi/DFL on September 27, 2016, 11:55:33 am ...or maybe Deutz FL812, depending on the necessary piston to wall clearance.
Tobi Title: Re: Raceengine Parts Post by: kever65 on September 27, 2016, 16:22:05 pm interested in cylinder heads, case and pistons. can you please tell me what went wrong with the engine? i see some damage on top of one of the pistons.
is there a built tread on here? in which car was it raced, the buggy? kind regards Davy Title: Re: Raceengine Parts Post by: Otto/DFL on September 27, 2016, 17:35:29 pm Hi Davy, PM send!
Title: Re: Raceengine Parts Post by: blue bullet on October 28, 2016, 16:51:41 pm what is the compression heigth of pistons and is in pin 22mn ?
thanks Laurent Title: Re: Raceengine Parts Post by: Otto/DFL on October 30, 2016, 18:20:04 pm Hi Laurent,
Yes, the pin diameter is 22mm, the compression hight is only 30mm, keeps the engine small! Bye Otto Title: Re: Raceengine Parts Post by: Otto/DFL on November 18, 2016, 07:43:15 am Up, with new prices! ;)
Title: Re: Raceengine Parts Post by: papysss on December 07, 2016, 13:37:12 pm What is there left?
Title: Re: Raceengine Parts Post by: Otto/DFL on December 08, 2016, 08:37:07 am Hi!
Everything minus the rockers! Thanks Otto Title: Re: Raceengine Parts Post by: Jukkis Maki on December 09, 2016, 07:06:56 am Hi
You have mail! Jukka |