The Cal-look Lounge

The Cal-look classifieds => Wanted => Topic started by: Lee.C on October 13, 2009, 15:37:34 pm



Title: Where the hell can I buy 24mm hex bar from!!!!!!
Post by: Lee.C on October 13, 2009, 15:37:34 pm
I have been searching the net for AGES and I can't find a supplier for 24mm Hex Bar - Can anyone help ??? ??? ???


Title: Re: Where the hell can I buy 24mm hex bar from!!!!!!
Post by: jick on October 13, 2009, 15:51:26 pm
this place seems to have it in 1" section in Aluminium.....you need to scroll down a few pages.....i know its not quite 24mm but it might be a start?

http://www.arenastock.co.uk/Arenastock-catalogue-2005.pdf


cheers dude....Jick,

what do you need it for?

just had another look......they do a 24mm in mild steel and stainless too..... ;)


Title: Re: Where the hell can I buy 24mm hex bar from!!!!!!
Post by: Lee.C on October 13, 2009, 21:18:01 pm
this place seems to have it in 1" section in Aluminium.....you need to scroll down a few pages.....i know its not quite 24mm but it might be a start?

http://www.arenastock.co.uk/Arenastock-catalogue-2005.pdf


cheers dude....Jick,

what do you need it for?

just had another look......they do a 24mm in mild steel and stainless too..... ;)

COOL cheers dude - I only just saw your reply  :)

This for a Patenten'd Monkiboy mod I am doing for my friends 68 http://cal-look.no/lounge/index.php/topic,7573.0.html  ;)

I had this idea ages ago and now I have the chance to try it out - Basiclly it has ALWAYS annoyed my how there is NO place to put a proper spanner on the Tracking arms on a vw so I have drawn up some plans for a small 40mm long section of 24mm hex bar that I will bore out internally to 19mm (diameter of tracking arms) then slide it onto the arms then run a bead of weld round each end (then dress the weld & paint)

So now you have a nice area where you can use a 24mm spanner to adjust your tracking - maybe its a little "overkill" but I just think it will help in the future  :)

I am also gonna do the same to the 2 framehorn bars for the rear truss bar so that can also be adjusted/preloaded easyily  :)



Title: Re: Where the hell can I buy 24mm hex bar from!!!!!!
Post by: Fritter on October 14, 2009, 04:18:13 am
http://www.onlinemetals.com/merchant.cfm?id=745&showunits=mm&step=2&sortby=od&top_cat=60


Title: Re: Where the hell can I buy 24mm hex bar from!!!!!!
Post by: jick on October 14, 2009, 09:27:18 am
thats a good idea dude, i just replaced all the track rod ends on my '59 so i know exactly what you mean.


Title: Re: Where the hell can I buy 24mm hex bar from!!!!!!
Post by: AutoManics on October 14, 2009, 11:22:16 am
I have done this mod before on various vehicles, easiest way is to buy nuts in the size you want and bore the middle out to the right size, looks tidy too! :)

You can see them in place here on my 4 bars.

(http://automanics.googlepages.com/ghia6.jpg/ghia6-custom;size:634,422.jpg)


Title: Re: Where the hell can I buy 24mm hex bar from!!!!!!
Post by: Lee.C on October 14, 2009, 12:03:56 pm
I have done this mod before on various vehicles, easiest way is to buy nuts in the size you want and bore the middle out to the right size, looks tidy too! :)

You can see them in place here on my 4 bars.

(http://automanics.googlepages.com/ghia6.jpg/ghia6-custom;size:634,422.jpg)

Hey thats not a bad idea about the Nuts but I have 4 cars to do in total and I want to make the spanner area slightly bigger than just a nuts width, Thanks for the pic though:)