|
Title: What H/P have you made with 48IDF's? Post by: drgouk on December 28, 2013, 00:03:59 am What H/P have you made with 48IDF's?
I am interested to see what kind of power you can make with a set of 48 idf's? Standard out of the box or modified. 250h/p possiable with some mods? Back at my old job we made 234h/p on a set of 48idfs on a 1900cc 16Valve alfa boxer, So I think they are almost there. Let me know your experiences. Thanks David Gouk Title: Re: What H/P have you made with 48IDF's? Post by: Taylor on December 28, 2013, 04:11:46 am Was the 16 valve individual runner or plenum?
Title: Re: What H/P have you made with 48IDF's? Post by: drgouk on December 28, 2013, 05:24:35 am Individual runner.
Title: Re: What H/P have you made with 48IDF's? Post by: Taylor on December 28, 2013, 05:44:36 am That's really good. I know 48 IDAs can make 250+ with 44 chokes. But I don't know what the biggest choke you can fit in an idf.
Title: Re: What H/P have you made with 48IDF's? Post by: drgouk on December 28, 2013, 05:54:49 am Taylor, I see Jaycee does 44 vents for the IDF. Maybe some shaft profiling and some custom stacks and you could get there.
Title: Re: What H/P have you made with 48IDF's? Post by: Taylor on December 28, 2013, 06:31:16 am A buddy of mine has 48 dell tri jets. He did a good amount of work on them. Stacks, profiling and all but only has 39 or 40 chokes. It makes 215 on pump gas and runs 11.60s. 80x94
Title: Re: What H/P have you made with 48IDF's? Post by: Neil Davies on December 28, 2013, 10:05:32 am I've got 48IDFs on my 2007cc motor. I've never dyno'd it, but it did run 12.50s in a 1640lb car (with driver) with slicks and a close ratio gearbox. I'd be interested to see what difference my IDAs make.
Title: Re: What H/P have you made with 48IDF's? Post by: javabug on December 28, 2013, 15:00:23 pm A buddy of mine has 48 dell tri jets. He did a good amount of work on them. Stacks, profiling and all but only has 39 or 40 chokes. It makes 215 on pump gas and runs 11.60s. 80x94 Taylor, do you know if he changed the trijet jetting? I'm exploring that on mine now. Title: Re: What H/P have you made with 48IDF's? Post by: BeetleBug on December 28, 2013, 16:00:13 pm 225 HP right here:
http://youtu.be/iFk4hdd_tG4 Title: Re: What H/P have you made with 48IDF's? Post by: drgouk on December 28, 2013, 20:57:30 pm 225 HP right here: http://youtu.be/iFk4hdd_tG4 BB, do you know of anyone back to backing them with IDA's? Title: Re: What H/P have you made with 48IDF's? Post by: drgouk on August 02, 2015, 03:07:38 am I have purchased a set of 48idfs to see what can be made with them. I will try them on my 2789cc street motor on the dyno. My plan is to drill the float chamber for a drain, Then I can install a sight tube, like the IDA ones from Jaycee. This way I can observe whats going on in the float chambers on the engine dyno. I will install some 2.5 Viton tipped needle valves and probably radially drill them for increased flow. Any thoughts or new info would be appreciated.
|