|
Title: Which pushrod tubes??!! Post by: chateau la fete on November 22, 2015, 21:43:40 pm Hi
Can anyone recommend which push rod tubes to use on a 2332 stroker motor?? Title: Re: Which pushrod tubes??!! Post by: chateau la fete on November 23, 2015, 00:12:54 am And main oil seal/gearbox shaft seal - silicone or genuine??
Title: Re: Which pushrod tubes??!! Post by: PPRMicke on November 23, 2015, 13:17:10 pm CSP Tubes
Seal Silicone (main) Gerbox NOS /// Micke Title: Re: Which pushrod tubes??!! Post by: richie on November 23, 2015, 17:36:05 pm Hi Can anyone recommend which push rod tubes to use on a 2332 stroker motor?? What heads are you using? cheers Richie Title: Re: Which pushrod tubes??!! Post by: chateau la fete on November 23, 2015, 21:31:35 pm Scat pro comp
Title: Re: Which pushrod tubes??!! Post by: richie on November 23, 2015, 22:59:08 pm Scat pro comp Ok so stock VW style, you can use genuine VW WBX and put the bigger end at the head or the newer CB stainless racing push rod tubes if you want a on piece design, after that its more personal choice with the 2 piece tubes cheers Richie Title: Re: Which pushrod tubes??!! Post by: chateau la fete on November 24, 2015, 20:27:31 pm Ok thanks for that
Title: Re: Which pushrod tubes??!! Post by: chateau la fete on November 27, 2015, 19:52:15 pm Sorry to be a pain!!
can you recommend which clutch disc (I have a Kennedy stage 2 plate)? Which release bearing? Basically the setup I have works really well for the street and used to run strip a little (I want to run strip next year). The equipment I have does not have any makers stamp on, so not sure what has been installed. I'm not new to this and know my way around an engine, but I am a bit new to the tried and tested equipment that is around today, a lot more of it!! (used to have quick vw's in the 90's (ported and polished, etc, not 'bolt on') and also have a charged 30HP. I want to install what works well and lasts in the right way. Thanks for any input Title: Re: Which pushrod tubes??!! Post by: richie on November 27, 2015, 20:06:54 pm Sorry to be a pain!! can you recommend which clutch disc (I have a Kennedy stage 2 plate)? Which release bearing? Basically the setup I have works really well for the street and used to run strip a little (I want to run strip next year). The equipment I have does not have any makers stamp on, so not sure what has been installed. I'm not new to this and know my way around an engine, but I am a bit new to the tried and tested equipment that is around today, a lot more of it!! (used to have quick vw's in the 90's (ported and polished, etc, not 'bolt on') and also have a charged 30HP. I want to install what works well and lasts in the right way. Thanks for any input No problem for me to help :) that's what forums are for, sharing information 8) I would use a super daikin disc, don't get the cheaper normal daikin Just about to do my 1st performance 25hp engine so maybe asking you questions next ;D cheers Richie Title: Re: Which pushrod tubes??!! Post by: chateau la fete on November 27, 2015, 23:39:15 pm Thanks
So do you think a standard release bearing (I have a close ratio IRS box, modified for an oval chassis) Vintage speed performance, check out "souring the Volkswagen", first published in '59. Very interesting read. Title: Re: Which pushrod tubes??!! Post by: chateau la fete on November 27, 2015, 23:41:41 pm Sorry, "souping the Volkswagen"
Title: Re: Which pushrod tubes??!! Post by: richie on November 28, 2015, 10:13:02 am Thanks So do you think a standard release bearing (I have a close ratio IRS box, modified for an oval chassis) Vintage speed performance, check out "souring the Volkswagen", first published in '59. Very interesting read. Yep, just a decent brand and you are good Title: Re: Which pushrod tubes??!! Post by: chateau la fete on December 11, 2015, 20:08:45 pm Just fitted a set of csp push rod tubes. Then went in very easily with only a small amount of pressure on the Spring. They are seated, but are they meant to go in so easily??!!
|