|
Title: custom rockers on the concpt 67 Post by: danny gabbard on May 20, 2008, 02:30:12 am just gettin started
Title: Re: kustom rockers on gabfabs 67 Post by: louisb on May 20, 2008, 11:54:49 am Nice work on that seem and the join at the b-pillar.
--louis Title: Re: kustom rockers on gabfabs 67 Post by: javabug on May 20, 2008, 13:03:51 pm Do you hammer your welds? That's a technique I'd love to learn. Sorry if this is an obvious question.
Title: Re: kustom rockers on gabfabs 67 Post by: danny gabbard on May 20, 2008, 16:17:20 pm after panel is tacked,that are tig welded I hammer between tack's ,to get edge of seam flat then weld but I use .023 mig wire for filet. never use rod thicker that appearent metal. then grind both sides if ya can get to them ,but only grind weld,not the sheet. then start the hammer process to raise low spots ,from heat from weldind or worpage.
Title: Re: kustom rockers on gabfabs 67 Post by: Zach Gomulka on May 20, 2008, 16:41:39 pm Is it still getting running boards of some sort? Or is the chrome getting attached straight to the rocker??
Looks nice 8) Title: Re: kustom rockers on gabfabs 67 Post by: danny gabbard on May 20, 2008, 16:47:03 pm the plan is to make some curved running board like on a new bug then kinda blend into fenders like a 35-7 ford and leave about 1/2 inch of area under door thats painted so you can see door gap .
Title: Re: kustom rockers on gabfabs 67 Post by: louisb on May 20, 2008, 18:06:45 pm Do you hammer your welds? That's a technique I'd love to learn. Sorry if this is an obvious question. Check out this thread over at metal meet. http://www.metalmeet.com/forum/showthread.php?t=798&highlight=mig+thin+sheetmetal While your there, check out the post by Danny on the air cleaner he did for Boyd Codington. I have pretty much been living on that forum the past couple of weeks trying to soak up as much as I can. (One of the reasons I have not been on here much lately.) I have been practicing and working with some junk fenders using what I have learned. (I also have a beater bag coming to try some custom shaping. ;D ) Lot of good information there on metal working. Sorry, not trying to hijack Danny's thread. --louis Title: Re: kustom rockers on gabfabs 67 Post by: danny gabbard on May 20, 2008, 21:32:58 pm louis try hammering into or onto the rubber mats that people stand on, same as a shot sack. next come's the spanish wheel
Title: Re: kustom rockers on gabfabs 67 Post by: louisb on May 20, 2008, 21:36:00 pm louis try hammering into or onto the rubber mats that people stand on, same as a shot sack. next come's the spanish wheel Yeah I am already drooling over an Imperial E-wheel. Trying to decide if I want to buy one pre-made or roll my own. Thanks for the tip on the mat, I will give that a try. My friend is also supposed to be bringing me an oak stump to play with. --louis Title: Re: kustom rockers on gabfabs 67 Post by: WCB Hitler's Hot Rod on May 21, 2008, 07:58:26 am Looks bitchen Danny. Hook me up. 8)
Title: Re: kustom rockers on gabfabs 67 Post by: javabug on May 21, 2008, 12:50:37 pm [Check out this thread over at metal meet. http://www.metalmeet.com/forum/showthread.php?t=798&highlight=mig+thin+sheetmetal I just signed up, will be having a look around there soon. Here's the tech post I had in mind when I asked: http://www.jalopyjournal.com/forum/showthread.php?t=32050 Really makes me want a nice gas set-up. Title: Re: kustom rockers on gabfabs 67 Post by: louisb on May 21, 2008, 13:58:57 pm Check out the Henrob 2000 is your looking into OA welding. I have been thinking of getting one myself.
--louis Title: Re: kustom rockers on gabfabs 67 Post by: javabug on May 21, 2008, 14:08:59 pm Yeah, that's the one I've been dreaming of. 8) Maybe someday...
Title: Re: kustom rockers on gabfabs 67 Post by: danny gabbard on May 21, 2008, 15:41:30 pm just get a tig guy's then you can weld just about anything, even the crack of dawn
Title: Re: kustom rockers on gabfabs 67 Post by: danny gabbard on April 28, 2010, 17:51:26 pm Here Ya go tom !
|