|
Title: engine for fastback Post by: nicolas on June 29, 2008, 22:05:44 pm Ok so i will make a small topic about the enginetrouble i have and to channel a bit all the help i have been getting so far.
a big thank you allready so Russel has offered to bring a 63 engine for type3 and that can work out, BUT it needs a bunch of parts to swap from 6 to 12 volts. - first a new flywheel, that i allready have -12volt dynamo that i have, but it needs a different coolhouse And a different pulley as it seems to be a different size. - all coolingtin is different, but in order to change i need to undo the exhaust, which can be a pita... i do however have a collector, but no muffler that can be used on regular heatingsystems. i also have been working on a spare 1600 dualport and the heads look not good. they have brown deposit on them that i can remove, but i think they overheated and may have problems with keeping CR... or if they are useable at all. the bottomend looks OK and the cam doesn't show any wear but i haven't taken the bottomend appart. and i was hoping not to do so and build it up from were i was now... any ideas are always welcome. thanks nicolas Title: Re: engine for fastback Post by: nicolas on June 30, 2008, 06:43:23 am look at the wrist pins on the pistons... if there is blueing then the head probably did over heat. if they aren't blued or impossible to get out, the heads may still be okay. they came out fine and were not blue, but i have to check again to make sure. the engine always ran fine so i didn't expect to see that on the heads... Title: Re: engine for fastback Post by: Russell on June 30, 2008, 08:31:15 am the engine
Title: Re: engine for fastback Post by: nicolas on June 30, 2008, 08:42:41 am works for me!
Title: Re: engine for fastback Post by: Dirk / DFL on June 30, 2008, 17:22:27 pm you need a 12V generator? I have one here, you can have it for a beer :-)
Title: Re: engine for fastback Post by: nicolas on June 30, 2008, 21:18:00 pm you need a 12V generator? I have one here, you can have it for a beer :-) thanks! but i do have a dynamo, that works, i also have the coolinghouse for the 12V dynamo. but if you have a GENERATOR, i'll buy you 2 beers! been looking for that conversion for a while now, but that is not the main worry at the moment. i always thought type 3's came with dynamo's... not too sure. i have been looking at my parts and it looks like i can make everything work. the big question is still, WILL it work??? but i have wednesday night and thursday to find that out. allready bought a clamp to hold the flywheel (finally) and a new seal that goes behind the flywheel, just in case. Title: Re: engine for fastback Post by: Russell on June 30, 2008, 22:48:01 pm its loaded and will be in chimay, belgium on wednesday as promised
Title: Re: engine for fastback Post by: nicolas on July 01, 2008, 08:26:48 am its loaded and will be in chimay, belgium on wednesday as promised thank you allready so much! will meet you there. Title: Re: engine for fastback Post by: Dirk / DFL on July 01, 2008, 16:35:09 pm Hmmm, its not a alternator.... I bring it and you can see, its a original VW replace-part, with sticker on it, for a typ 3 engine....
Title: Re: engine for fastback Post by: nicolas on July 01, 2008, 17:17:53 pm Hmmm, its not a alternator.... I bring it and you can see, its a original VW replace-part, with sticker on it, for a typ 3 engine.... thanks see you there! Title: Re: engine for fastback Post by: nicolas on July 03, 2008, 13:28:57 pm alright picked up the engine yesterday at chimay and went to work on it right when i got home. worked till 1:30am to have it in the car and change a few things to convert it to 12V. it is a hassle on a type3. so i have switched the pulley, dyno, cutoff,cooling and distributor. and in had to take off the exhaust. got up this morning and went to get some j-tubes and a cheap ass muffler to install as the original one needs some more WD40 to get back on and i don't have time for that. also got a 6V starter that might or might not work... fingers crossed i am off to the garage again.
Title: Re: engine for fastback Post by: Neil Davies on July 03, 2008, 13:42:08 pm Best of luck to you Nicolas! Enjoy EBI!
Title: Re: engine for fastback Post by: wolfswest on July 03, 2008, 13:49:35 pm hope to see your car there, and not on a trailer. keep up the good work! ;)
Dem Title: Re: engine for fastback Post by: j-f on July 03, 2008, 14:30:12 pm Good luck Nico.
Hope to see you there with your Fastback. Title: Re: engine for fastback Post by: nicolas on July 04, 2008, 11:12:53 am ah i just gave up!
the engine runs but very bad and i can't get the brakes done, they leak again, the reartorsionbars i switched set the car too low as well... too much work to get it all done. so i'll be at there, but not the car. :'( Title: Re: engine for fastback Post by: JS on July 04, 2008, 16:30:15 pm #&!#/"$%/&!!!!! >:(
Well, see you tonight at the SCC bus, Nicolas. :) Title: Re: engine for fastback Post by: wolfswest on August 05, 2008, 20:06:58 pm nicolas,
how's your new engine coming together? Everything on schedule? ??? Dem Title: Re: engine for fastback Post by: nicolas on August 05, 2008, 21:37:10 pm nicolas, how's your new engine coming together? Everything on schedule? ??? Dem no engine yet, thursday should be the big day. hope Steve can finish it up as the SCC is coming close and i need a lot off stuff to be checked on the car beforehand. Title: Re: engine for fastback Post by: wolfswest on August 06, 2008, 09:05:09 am yep, fingers crossed!
I can't make it to SCC but I would like to make it to SCC one of the next years. Sounds like an awsome roadtrip... Keep us informed! |