OTHER CAM?

[SPEEDWELL66]

hola amigos!


i'm planning to rebuild my 2054CC but i want to make some changes. im actually using the engle w125 whit 1:25 rokers so here is my question:

wish cam can i use instead of the w125?

these are the parts of my 2054CC:

48 idas
041's "D" ported heads whit 40x35 valves, dual springs and 9.5 to 1 compression
kennedy stage 1
daiken plate
straight cut's
30mm shadeck pump
1 3/4 headers whit a magnaflow

thanks for your help friends!


THE MEXICAN RACER

[Jim Ratto]

why do you want to change from 125?
The Pauter R6E8 in my 2165 is docile, yet fierce above 3800 to just under 7000. I run it with Scat 1.25

[Bruce]

A better thing to do is upgrade your heads.  By increasing to a 42mm valve, you'll make way more hp than any cam change.

[Torben Alstrup]

And reduce the header to a 1 5/8"
I prefer the Scat C45 over the Engle 125. As much or even more power (at least torque) and more quiet running. But it depends on what youre looking to improove.
T

[SPEEDWELL66]

thanks a lot for your response amigos!

o.k. i like a lot the w125 cam but like i said, i'm disaselmbling my engine so if there is a beter cam to use in my engine is fine!

the pauter cam that "the other one" said sounds good, but where can i buy that cam? because i went to the pauter site and can't find it.....

hey bruce are you talking about made my heads 42x37? but those valves will work whit my "drive to the shows-thursday night dragstrip" vw cruiser?

yep, i was tinking about the size of my headers torben...thanks for the advise amigo! and...............definetly you tink that the c45 works better than the w125? remenber that i want to keep my 1:25 rokers!


gracias.............

THE MEXICAN (TRYING TO BE  ) RACER!

[kingsburgphil]

I ran a W130 and stock rockers decades ago in a similar motor (ex DKP) no complaints, period.  (Except from the losers behind me)

[Bruce]

hey bruce are you talking about made my heads 42x37? but those valves will work whit my "drive to the shows-thursday night dragstrip" vw cruiser?

yes.  your cam is already a pretty big cam, you wouldn't want to bigger with your small heads.  Bigger heads is what you need. 
A smaller exhaust too.

[SPEEDWELL66]

hmmmmmmmm, a 130 engle, nice option............


so the w125 is already a nice cam right? i'll try to sold my heads or i shoul try to modify them change the valves..


gracias amigos!

[Zach Gomulka]

Sorry I didn't answer your PM Luis, been busy!!
I agree the exhaust is too big, you're loosing some torque there. I've never ran the 125, but for your combo it looks right to me

[SPEEDWELL66]

thanks zach!!!!


about the headers, i'm planning to sell those headers and even the magnaflow.. i'm about to turn 80's and buy some merged 1 5/8 and a dual quiet pack merged mufflers from bugpack!   what do you think amigos?


THE MEXICAN RACER

[Zach Gomulka]

I like the sound of the Magnaflow but I like the looks of dual QP's, your call!

[SPEEDWELL66]

I like the sound of the Magnaflow but I like the looks of dual QP's, your call!

yep i like it too but i want to go "old school"  in fact i'm going to change the hole look of mi engine 

thats why im going to sell the headers and the muffler. the thing is that both (muffler and headers) are big flange  and as you amigos said, it will be better if i use 1 5/8 headers, right?

right know here is how it looks my engine:


but its been a lot of years whit the same look, i want a change! 


saludos amigos!

THE MEXICAN DUDE

[Zach Gomulka]

You're motor looks pretty good Luis. One of my favorite things about your car has always been the "Hecho En Mexico" badge

[SPEEDWELL66]

You're motor looks pretty good Luis. One of my favorite things about your car has always been the "Hecho En Mexico" badge

  proudly built in the U.S.M (united states of mexico)



THE MEXICAN VATO

[SPEEDWELL66]

hey amigos, what do you think about this heads?

they are 42x37...

take a look and let me know if a should try this on my engine instead of changing the cam.









THE BEAN BOY