The Cal-look Lounge
Welcome, Guest. Please login or register.
Did you miss your activation email?
November 22, 2024, 14:13:39 pm

Login with username, password and session length
Thank you for your support!
Search:     Advanced search
351205 Posts in 28655 Topics by 6853 Members
Latest Member: Hacksaw Racing
* Home This Year's European Top 20 lists All Time European Top 20 lists Search Login Register
+  The Cal-look Lounge
|-+  Cal-look/High Performance
| |-+  Pure racing
| | |-+  IDA Ballpark Jetting with F4's
« previous next »
Pages: [1] Print
Author Topic: IDA Ballpark Jetting with F4's  (Read 4793 times)
neil68
Hero Member
*****
Posts: 538



« on: April 12, 2016, 05:02:25 am »

Anyone have suggestions for jetting IDA's with F4 emulsion tubes?  Running Raptor 44 mm venturies, MS230 heads, Raptor 6908 camshaft and 10:1 CR with 94 AKI (98 RON) pump fuel.

Would like some ballpark suggestions to start with, as it might be a while until the next Dynojet session.

Thanks!
Logged

Neil
Der Kleiner Rennwagens
'68 Beetle, 2332 cc, 204 WHP
12.5 seconds @ 172 KM/H (107.5 MPH)
Dynojet Test:  https://www.youtube.com/watch?v=M9B_H3eklAo
Jim Ratto
Hero Member
*****
Posts: 7121



« Reply #1 on: April 12, 2016, 23:51:09 pm »

180 main with 200-205-210-215 air.
Sorry to be vague on air.
My car has a very narrow window as to what air corrector it runs well with, using F4.
For example, with 165 main and 185 air in F4, it runs incredibly rich at 42-4700 rpm under load. Move to 200 and this goes away and the AFR shows 12.3-12.5:1 WOT through 7000 rpm. Go to 215 air and the AFR shows 13.2-13.7 at very high rpm (6000+).
I haven't seen an F2 tube behave this way and be so picky about air corrector, but I still maintain my car runs its best, throttle response wise, with F4

Logged
neil68
Hero Member
*****
Posts: 538



« Reply #2 on: April 14, 2016, 04:54:58 am »

Thank you!
Logged

Neil
Der Kleiner Rennwagens
'68 Beetle, 2332 cc, 204 WHP
12.5 seconds @ 172 KM/H (107.5 MPH)
Dynojet Test:  https://www.youtube.com/watch?v=M9B_H3eklAo
Jim Ratto
Hero Member
*****
Posts: 7121



« Reply #3 on: April 14, 2016, 05:06:54 am »

no prob
please keep us posted how they work for you

Jim
Logged
neil68
Hero Member
*****
Posts: 538



« Reply #4 on: April 16, 2016, 05:29:01 am »

Re-assembled the engine and took it for a drive today.  Very impressed with how smooth it runs at low rpms, driving around the neighbourhood.  It seems smoother with the F4's than the previous F2's.

Current jetting:

F4
185 main
220 air
65 idle
120 idle air
3.0 mm needle valve
44 Raptor venturies

It will be interesting to see how this drives on the 1/4-mile.
« Last Edit: April 16, 2016, 05:33:59 am by neil68 » Logged

Neil
Der Kleiner Rennwagens
'68 Beetle, 2332 cc, 204 WHP
12.5 seconds @ 172 KM/H (107.5 MPH)
Dynojet Test:  https://www.youtube.com/watch?v=M9B_H3eklAo
fish
Full Member
***
Posts: 224



« Reply #5 on: April 16, 2016, 16:32:19 pm »

Good to hear mate, i might try the F4s myself.
There is an opportunity to buy a set of 51 IDAs, i wonder how they would run on a street 2180, GB309 and Fred Simpson 42x36
Logged

Had a fight with a Magneto, it won!
neil68
Hero Member
*****
Posts: 538



« Reply #6 on: July 11, 2016, 03:49:42 am »

Finally made it to the drag strip for some testing.  Used the above jet stack, but ran slower than last year (it was very humid, which is rare here, so that may have been a factor).  Elevation is 670 m.

Tried a couple main jets 185 & 180 (both are recommended with 44 Raptor vents), as well as airs 220 and 200, but ran out of time after 5 races.  Then put in the F2's for back-to-back comparison and ran 0.15 seconds faster.  So far, the engine prefers the F2's.

Will experiment again in two weeks at the next race...maybe with 170 mains and and other airs.
Logged

Neil
Der Kleiner Rennwagens
'68 Beetle, 2332 cc, 204 WHP
12.5 seconds @ 172 KM/H (107.5 MPH)
Dynojet Test:  https://www.youtube.com/watch?v=M9B_H3eklAo
Pages: [1] Print 
« previous next »
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!