2.5 liter Type 1 engine parts

[karl h]

http://www.thesamba.com/vw/classifieds/detail.php?id=835854

PM me with any questions

[karl h]

parts availible seperately:
CB pentroof case, no studs or cylinderspigots drilled, new 700€
100mm bore nicasil cylinders and pistons from porsche turbo, set up for waterboxer studpattern, pistons machined flat, new 1000€
CB 78mm crank, checked, rods reground first under, 5.4 CB rods set, rod bearings 700€
Competition eleminators, welded for 52x40 valveseats (installed), no stud pattern, no bores, manley custom 8mm stem 52x40 valves, K 800s, titanium retainers, keepers (all new) 1000€
1 ¾“ merged header with 2 ½“ Apple Racing muffler, only a few km, 350€
51,5 IDA Webers, used but working, 700€

[karl h]

CB pentroof case, no studs or cylinderspigots drilled, new 700€
100mm bore nicasil cylinders and pistons from porsche turbo, set up for waterboxer studpattern, pistons machined flat, new 1000€
CB 78mm crank, checked, rods reground first under, 5.4 CB rods set, rod bearings 700€
Competition eleminators, welded for 52x40 valveseats (installed), no stud pattern, no bores, manley custom 8mm stem 52x40 valves, K 800s, titanium retainers, keepers (all new) 1000€
1 ¾“ merged header with 2 ½“ Apple Racing muffler, only a few km, 350€
51,5 IDA Webers, used but working, 700€

bump
or make me an offer i cant refuse

[karl h]

bump

[karl h]

CB pentroof case, no studs or cylinderspigots drilled, new 700€ SOLD
100mm bore nicasil cylinders and pistons from porsche turbo, set up for waterboxer studpattern, pistons machined flat, new 1000€
CB 78mm crank, checked, rods reground first under, 5.4 CB rods set, rod bearings 700€
Competition eleminators, welded for 52x40 valveseats (installed), no stud pattern, no bores, manley custom 8mm stem 52x40 valves, K 800s, titanium retainers, keepers (all new) 1000€
1 ¾“ merged header with 2 ½“ Apple Racing muffler, only a few km, 350€
51,5 IDA Webers, used but working, 700€

[Jürgen/DFL]

Hi Karl
do you still have the 51,5 IDAs??
Best regards

Jürgen

[karl h]

100mm bore nicasil cylinders and pistons from porsche turbo, set up for waterboxer studpattern, pistons machined flat, new 1000€ (comes with a used waterboxer case with cut off waterjackets)
CB 78mm crank, checked, rods reground first under, 5.4 CB rods set, rod bearings 500€
Competition eleminators, welded for 52x40 valveseats (installed), no stud pattern, no bores, manley custom 8mm stem 52x40 valves, K 800s, titanium retainers, keepers (all new) 1000€
1 ¾“ merged header with 2 ½“ Apple Racing muffler, only a few km, 300€
51,5 IDA Webers, used but working, 700€

yes i still have these jürgen, but i decided to sell only if the pistons/cylinders are sold

i had quite some interrest in these parts, lots of email conversations and pics sent. then people seem to fall off the face of the earth? come on, is a mail or PM with "no thanx" or at least "get lost" asked too much?