Temporary insanity?
For sale: ’55 street/strip Cal-look beetle, rolling carThe ‘55 started as a low-mileage swedish rust-free car, receiving a pan-off resto and a quality Jungle Green paint job on bare metal in the mid-90s. Everything in the car was rebuilt back then. I have driven about 22.000km with it in total since rebuild, including a couple of hundred passes down the strip.
Cal-look winner in BugRun #20, featured in Ultra VW and Wheels (Sweden) in 2004 and “Best attitude” award in SCC 2008.
The car is in very good condition, but please note that the 10 years of driving and racing shows when looked closely - it wouldn’t score top points in a ‘DRKC event’, but it
carries its few paint chips with pride. Also, the engine compartment has been slightly cut to fit the large valve covers of the current engine, and under the carpet there are a couple of drilled holes where there used to be nitrous bottle brackets and solenoids, oil-cooler brackets etc.
On the strip it launches pretty well; it ran low 1.5sec 60ft times first time out with the current suspension, and drives straight and safe 11s at almost 190km/h. NHRA legal to 11.00sec.
Please note also that even though I mostly describe the racing side of the car, it is still a real full steel/glass/interior street car, not a gutted race car with plates.
Included in the rolling car:
• Top of the line dragrace T1 transmission, built by Sam at Rancho, German 3.88 r&p : FTC/Weddle 3.55-2.06-1.44-1.09 gears, aluminum spool, synchros, gusseted case, Timken conversion, HD cover etc ($2700, 12 month old, less than 20 passes since new).
• Karpiola ‘unbreakable’ axles
• Race-weight Erco wheels, 7” and 4.25”x15 (12 month old, 300km since new)
• MH 235-60-15 dot slicks, MH 24x3.6x15 dot front runners (12 month old, less than 20 passes since new)
• 12mm press-in studs and open-end lug nuts
• Koni adjustable drag-race prepped rear shocks (12 month old)
• 28mm SAW rear torsion bars
• Adjustable rear spring plates
• Custom narrowed rear with custom Karpiola 1½” narrowed axles (‘mini-tubbed’ 1½” each side - fits 10.5” tires under stock fenders with ½” space on both sides!!!)
• Narrowed adjustable front beam (1" each side)
• Line-lock
• Porsche 914 seats (could use new upholstery)
• TMI panels
• GB 40% shifter
• Simpson 5-point 3” harness for driver (valid thru 10/2012)
• NHRA legal 5-point roll bar
• Electrical main switch in rear apron
• MSD Digital-6 ignition, MSD coil and MSD rpm-window switch (e.g. for nitrous)
• G-tech tachometer w/ sequential shift light, 8-channel datalogging and 8Mb extra memory (
http://www.gtechpro.com/egs.html)
• Autometer Sport Comp 2 5/8” oil pressure, oil temperature and cylinder head temperature gauges
• No engine, fuel cell, pump, lines or regulator, but
everything else is there!
Pictures attached are from 2008 and 2009 seasons. I have lots more from the past 10 years.
Price 10.000eur firm. Install your engine and fuel system and go for a cruise or racing! Cheaper with standard transmission, wheels...
Located in Helsinki. Delivery to SCC 2009 can be arranged (add ferry + tow car cost for 1200km round trip, approximately 600-700eur?).
- SOLD - SOLD - SOLD -
Jyrki
+358-40-7432391
jyrki dot laune at gsg dot fi
ps. The reason for testing the water is that I have recently found myself focusing on my project ’53 beetle (pretty much a race car), the fact that even without the ’55 there would be enough street beetles in the family, and, last but not least, at the moment I have lost interest to race and develop the ‘55 further to squeeze tenths off the et’s.