2919CC T1 (Turnkey being built) Jeff Denham

[71CALRIPPER]

Right this kills me to do ths but the fact is I need to get on the property ladder before Christmas so needs Must

What you are buying is a Fully turnkey 4 Inch bored motor being built but Jeff Denham, this is very much the same as his own beast which made silly HP and was driven through the searing heat raced and driven home again.

Turnkey - Carbs- Cooling- Exhaust etc


I will supply predicited figures and build time later. HP Compression etc .

Here is the Parts List ( few things may have been missed )

90MM SCAT PART# 8-90-4444F SCATS TOP OF THE LINE RACING/STREET CRANK
CHEVY ROD JOURNAL,ALL TYPE 4 MAINS.      

SCAT 12-VOLT 8 BOLT 200MM FLANGE FLYWHEEL PART#60083.

SCAT/ARP BIG HEAD 7/16s FLYWHEEL BOLT,S.

SCAT FLYWHEEL FLANGE SEAL.

1 SET 5.880 EAGLE 5/16s ARP 2000 BOLT,S CLEARENCED AND BALANCED 22MM RISTPIN.

JD1 CUSTOM GRIND SC1 BILLET STREET/RACE T1 CAM.

SET T4 BMW MAIN BEARING SET.

SET CLEVITE 77 CHEV STD ROD BEARING,S.

SET DOUBLE THRUST CAM BEARINGS.

SET SCAT REG LUBE A LOBE LIFTER,S.

SET CRANK/CAM STRAIT CUT MAGNUM GEARS.    

JD1 RAISED DECK MODIFIED 4INCH BORE T1 ALUIM CRANKCASE WITH CENTER MAIN THRUST.

SET JD1 CUT TO LENGTH FINNED POWER HONED 101.6 CLYINDER,S.

SET JE 22MM PIN 101.6 FORGED RACING/STREET PISTONS AND RING PACK.

SET .040 101.6 COPPER HEAD GASKET,S.

SET BUGPACK 10MM EQUAL LENGTH HEAD STUD,S AND HARDWARE.

SET JD1 ANGEL FLOW 52X40 CNC PORTED AND BLENDED STREET/RACE CLY HEADS. MATCH PORTED 51.5 ROUND PORT MANIFOLDS. AND MODIFIED AF VALVE COVERS.            

SET JD1 MODIFIED 1.4 RATIO ROCKERS.

SET MANTON STREET/RACE 3/8 CUSTOM PUSH RODS.

JD1 ALUIM SPRING LOADED PUSH ROD TUBES SATIN ALUIM FINISH.

BERG 4QT STREET/RACE SUMP WITH 3/4 PICK UP.

JD1 30MM WET SUMP OIL PUMP AND FULL FLOW COVER.

JD1 CUSTOM BUILT 2INCH AF HEADER SYSTEM WITH MUFFLER.

SET JD1 POWDER COATED T1 FAN SHROUD AND CLY COVERS CUSTOM FITTED TO 2919 T1 ENGINE.

WELDED AND BALANCED T1 FAN.

T1 ALTERNATOR AND PULLEY SET WITH POWER PULLEY BELT.

JC PERF POWER PULLEY AND NUT AND WASHER.

SET 51.5 IDA CARB,S WITH BIG MOUTH STACKS.

BERG IDA FANSROWD CARB LINKAGE.

KENNEDY STAGE 3 BALANCED WITH JD1 STREET/RACE CLUTCH DISC AND HARDWARE.

VERTEX   MAGNETO IGNITION SYSTEM WITH WIRES.

Please be aware this is what it started out like..









So with engine prices these days its hard to put a price on such a custom engine, that will have no miles on it etc.

So £7000 gets you this motor, in many ways the money you save is like having all the custom machine work done

[71CALRIPPER]

This was Jeffs engine installed in his street car

[Rick Meredith]

Is the motor in the US or GB?

[71CALRIPPER]

Hi there the motor is still with Jeff being built so in the US 

[Rick Meredith]

Hmmm... Interesting. 

[Rick Meredith]

Well after discussing it with my brain trust, the verdict is that it won't be suitable for my '67. 

It is a heck of a deal though. Good luck with the sale.

[71CALRIPPER]

Brain vs Heart lol


Yeah my loss is somebody's gain for sure

[dave.d]

rob you have pm 

[leec]

rob you have pm 

Dave, are you thinking what I think you are thinking? 

Lee

[71CALRIPPER]

All PMs replied to will start to put this on the SAMBA and other forums soon

[71CALRIPPER]

Pending sale

[DaveN]

Still waiting for this to arrive. 

[Jesus]

Mad its been three years, youd think it'd arrive in that kinda time frame!

[UltraOrange67-2443]

 

[speed7]

If I think what Lee is thinking what Dave is thinking .... 

[DaveN]

Right this kills me to do ths but the fact is I need to get on the property ladder before Christmas so needs Must

What you are buying is a Fully turnkey 4 Inch bored motor being built but Jeff Denham, this is very much the same as his own beast which made silly HP and was driven through the searing heat raced and driven home again.

Turnkey - Carbs- Cooling- Exhaust etc


I will supply predicited figures and build time later. HP Compression etc .

Here is the Parts List ( few things may have been missed )

90MM SCAT PART# 8-90-4444F SCATS TOP OF THE LINE RACING/STREET CRANK
CHEVY ROD JOURNAL,ALL TYPE 4 MAINS.      

SCAT 12-VOLT 8 BOLT 200MM FLANGE FLYWHEEL PART#60083.

SCAT/ARP BIG HEAD 7/16s FLYWHEEL BOLT,S.

SCAT FLYWHEEL FLANGE SEAL.

1 SET 5.880 EAGLE 5/16s ARP 2000 BOLT,S CLEARENCED AND BALANCED 22MM RISTPIN.

JD1 CUSTOM GRIND SC1 BILLET STREET/RACE T1 CAM.

SET T4 BMW MAIN BEARING SET.

SET CLEVITE 77 CHEV STD ROD BEARING,S.

SET DOUBLE THRUST CAM BEARINGS.

SET SCAT REG LUBE A LOBE LIFTER,S.

SET CRANK/CAM STRAIT CUT MAGNUM GEARS.    

JD1 RAISED DECK MODIFIED 4INCH BORE T1 ALUIM CRANKCASE WITH CENTER MAIN THRUST.

SET JD1 CUT TO LENGTH FINNED POWER HONED 101.6 CLYINDER,S.

SET JE 22MM PIN 101.6 FORGED RACING/STREET PISTONS AND RING PACK.

SET .040 101.6 COPPER HEAD GASKET,S.

SET BUGPACK 10MM EQUAL LENGTH HEAD STUD,S AND HARDWARE.

SET JD1 ANGEL FLOW 52X40 CNC PORTED AND BLENDED STREET/RACE CLY HEADS. MATCH PORTED 51.5 ROUND PORT MANIFOLDS. AND MODIFIED AF VALVE COVERS.            

SET JD1 MODIFIED 1.4 RATIO ROCKERS.

SET MANTON STREET/RACE 3/8 CUSTOM PUSH RODS.

JD1 ALUIM SPRING LOADED PUSH ROD TUBES SATIN ALUIM FINISH.

BERG 4QT STREET/RACE SUMP WITH 3/4 PICK UP.

JD1 30MM WET SUMP OIL PUMP AND FULL FLOW COVER.

JD1 CUSTOM BUILT 2INCH AF HEADER SYSTEM WITH MUFFLER.

SET JD1 POWDER COATED T1 FAN SHROUD AND CLY COVERS CUSTOM FITTED TO 2919 T1 ENGINE.

WELDED AND BALANCED T1 FAN.

T1 ALTERNATOR AND PULLEY SET WITH POWER PULLEY BELT.

JC PERF POWER PULLEY AND NUT AND WASHER.

SET 51.5 IDA CARB,S WITH BIG MOUTH STACKS.

BERG IDA FANSROWD CARB LINKAGE.

KENNEDY STAGE 3 BALANCED WITH JD1 STREET/RACE CLUTCH DISC AND HARDWARE.

VERTEX   MAGNETO IGNITION SYSTEM WITH WIRES.

Please be aware this is what it started out like..









So with engine prices these days its hard to put a price on such a custom engine, that will have no miles on it etc.

So £7000 gets you this motor, in many ways the money you save is like having all the custom machine work done

still waiting for the rest of these parts to be sent

[Richierich56]

  WOW

[Nikov]

That's a shameful amount of time 

[DaveN]

Exactly. Great customer service!

[Trond Dahl]

Very sad and dissapointing at a minimum. Saw he ws just on facebook posting so he is alive at least

[DaveN]

Probably because a bit of noise is being made about the shit way he runs his business.  I'm going to post it on the samba soon

[Richierich56]

Has he at least corresponded with you regarding the subject?

[DaveN]

No not yet

[vwhelmot]

What parts are missing?

[DaveN]

What parts are missing?

Camshaft
Camgear
Bearings
Lifters
flywheel oil seal
crank shaft timing gear
Head studs
Head gaskets
1.4 rockers
pushrods
pushrod tubes
Berg 4 qt sump
Oil pump
muffler
pulley nut
clutch plate and clutch disc
Vertex magneto
crank case hardware kit.
Berg carb linkage.

Afew ££££s worth.  not something I can replace easily.

[vwhelmot]

Yes, that's not something you can write off. I would be demanding my money back. For whatever reason given, a refund for the parts should have been given by now and at least a 'sorry but I can`t supply you with' .  I get annoyed when I hear of this sort of thing, you can only be so nice for so long.  Its just not fair and not right.

[Nikov]

Yes, that's not something you can write off. I would be demanding my money back. For whatever reason given, a refund for the parts should have been given by now and at least a 'sorry but I can`t supply you with' .  I get annoyed when I hear of this sort of thing, you can only be so nice for so long.  Its just not fair and not right.

^^^This to the power of infinity. Way, way beyond being polite now.

[DaveN]

its a bit more difficult than asking for a refund. I have un known to me at the time, purchased a "contract " for the engine which means dealing with Jeff is my responsibility,  I have already been to court in the UK over this.

[vwhelmot]

Oh shit. Sorry to hear this mate.

[Rocket Ron]

its a bit more difficult than asking for a refund. I have un known to me at the time, purchased a "contract " for the engine which means dealing with Jeff is my responsibility,  I have already been to court in the UK over this.

The courts suck balls, that for sale add doesn't read like you were buying a contract to me Dave.

Hope you get a resolution to this soon, it's been way too long.

Regards Ron